** if you turn off GPS the next time you read in dev/bus/usb/001/002. When the GPS reads data, the led flashes indicating that we have more than 4 satellites are available. *** Remember that the data read situandolo in a space open to the sky. THE USB GPS IS READY TO NAVIGATE WITH MAPS Other models of GPS can works r at a different speed, to configure for each case, the baud rate correct. If it is necessary, order that-speed from console with: “stty -F /dev/ttyUSB0 ispeed 4800” With the command “cat < /dev/ttyUSB0” we can see from the console the data read by the GPS. ** Note The GPS takes a chip SIRF III that transmits data at a speed of 4800 baud rate.
This link is the Android APP that runs the GPS by Serial port Prolific Pl2303 on android devices descargaló and check that your android device is compatible:
Android 3.2 and higher versions of the operating system (compatible with Android 5.0, 6.0, 7.0) Android device (tablet / phones) with support host mode USB
The library of drivers PL2303 Android JAVA allows customers and developers to write Android applications to interface their devices PL2303 RS-232 / UART with millions of devices USB host Android as smartphones, tablets, and smart tvs. Prolific provides a solution driver API USB host Android (permission is NOT needed for root) for connecting devices that are USB-to-serial PL2303 devices with Android support mode API USB host. VALID FOR ALL VERSIONS OF ANDROID FROM 2.3 to 7.0 ADAPTER USB GPS SILICON or ND-105C / BU-353 with chip Prolific PL2303 USB-serial UART GPS Also works with micro-USB port on the Host. ANDROID TABLET WITH PERMISSIONS (does not need ROOT permissions) WITH A USB HOST PORT.
(1,000 knots) max.ĭimension: 2.32 "x 1.65" x 0.82 "(59mm x 47 mm x 21 mm)Īmplifier low noise Amplifier Gain w / out cable: 27 dB TypicalĬurrent: 15mA max 5VDC MANUAL FOR INSTALLATION OF ADAPTER GPS USB ANDROIDEste manual is used to install all Models of GPS receivers USB of the brands SILICON® and Glogalsat ® that work with Chip PL2303 EXAMPLE GLOBALSAT BU-353 Speed of transfer of GPS: settings of the software command (default: 4800, n, 8,1 for NMEA)ĭynamic acceleration of the condition: limit less than 4gĪltitude limit: 18,000 meters (60,000 feet) max. Output data GPS: command GGA, GSA, GSV, RMC, VTG, GLL v2.2 (VTG and GLL are optional) NMEA 0183 protocol MEA0183 V3.0 and supports Horizontal position: > position, velocity, altitude, status and control Characteristics Electrical Characteristics (Receiver) The software may have its own system requirements, please refer to the software vendor for more information. USB port and a navigation software compatible with NMEA. GPS receivers Globalsat USB require a laptop computer with a Windows or Macintosh with a CDROM *, USB GPS receiver - CD-ROM driver with user's Guide and test utility for WIN and Mac o / S * PC, LAPTOP, TABLET OR NETBOOK ADAPTER USB GPS TO NAVIGATE ON-SCREEN PowerBook.ĬOMPATIBLE ALL WINDOWS XP VISTA / WIN 7 / WIN 8 / LINUX / MAC The cable is long 1.5 m and has a USB connector on its end to connect with a laptop computer / ibook. Their applications include and are not limited to, marine, aerial, and commercial, fire trucks, police cars, buses, utility vehicles and the long-distance transport.
Has the latest GPS chipset SiRF Star IV, and with a patch antenna for a better signal precision. Chip Prolific PL2303 compatible cvon WAAS is magnetic and waterproof with a non-slip base. FOR VEHICLE, BOAT, AIRCRAFT, MOTORCYCLE ETC. The GPS receiver BU-353-S4 IS THE LATEST MODEL OF GPS RECEIVER. (EXPERIMENTALLY TESTED ON VERSIONS OF Android (2/ 3 / 4 /5)
WINDOWS XP, Vista system (32-64) , win7 operate system (32-64) WINDOWS 8, Mac OS system.
ADAPTER USB GPS RECEIVER SIRF STAR IV Waterproof for outdoor use / magnetic base GLOBALSAT BU-353-S4 WINDOWS - LINUX -MAC - Android (2/ 3 / 4 /5)